Upon completion of your training and high-risk assessment, the assessor will issue you with either an Assessment Summary (AS) or a Notice of Satisfactory Assessment (NSA) via email.
If you receive an AS you will need to complete further study or operator training before resitting the section in which you were found to be not yet competent. This needs to be completed within 60 days of the date of issue of the AS.
If you receive an NSA via email, there will be a link included that will prompt you to apply for your High-Risk Licence online through the MyServiceNSW Portal. You may be required to attend a Service Centre for a new Photo. Your High-Risk Forklift Licence will be mailed to you by SafeWork within 28 days of receiving your application. Your application must be submitted within 60 days of completing the assessment, or you will be required to complete the full training and assessment again.
This unit specifies the skills and knowledge required to safely operate a slewing mobile crane with a Maximum Rated Capacity (MRC) up to 60 tonnes in accordance with all relevant legislative responsibilities. Competence in this unit, does not in itself result in a High-Risk Work Licence (HRWL) to operate this plant.
Slewing mobile crane means a mobile crane incorporating a boom or jib that can be slewed, but does not include:
- A front-end loader
- A backhoe
- An excavator
- Or other earth moving equipment, when configured for crane operation.
A person performing this work is required to hold a slewing mobile crane with an MRC up to 60 tonnes HRWL.
This unit requires a person operating a slewing mobile crane with an MRC up to 60 tonnes to: plan for the work/task prepare for the work/task perform work/task pack up .
Licensing/Regulatory Information
Legislative and regulatory requirements are applicable to this unit of competency.
This unit is based on the licensing requirements of Part 4.5 of the Model Work Health and Safety (WHS) regulations and meets Commonwealth, state and territory HRWL requirements.
The National Assessment Instrument (NAI) is the mandated assessment for the HRWL to operate the relevant licensing class as detailed in this unit.
1 Plan work/task
1.1 Task requirements are identified from work orders or equivalent, a lift plan is confirmed with associated personnel and a site inspection is conducted in accordance with workplace procedures
1.2 Work area operating surface is confirmed to determine ground suitability for operational use of mobile crane in accordance with lift plan, safe work and workplace procedures
1.3 Mobile crane Rated Capacity (RC) and the lifting gear Working Load Limit (WLL) are established and suitable for the load/s and work/task requirements in accordance with manufacturer requirements and workplace procedures
1.4 Appropriate paths for operating the mobile crane and moving and placing load/s in work area are assessed and determined in accordance with workplace procedures
1.5 Relevant hazard identification and risk elimination/control measures are applied and advised to associated personnel in accordance with workplace procedures
1.6 Traffic management plan implementation is confirmed in accordance with workplace procedures
1.7 Appropriate communication procedures are identified with associated personnel in accordance with workplace procedures
1.8 All crane and lifting operations are confirmed to ensure relevant work area requirements are correct in accordance with a lift plan and workplace procedures
1.9 Information required to ensure that lifting equipment and gear inspection, use, maintenance and storage complies with manufacturer requirements is obtained and interpreted
2 Prepare for work/task
2.1 Consultation with workplace personnel is established and maintained to ensure all crane and lifting operations are clear and consistent with site requirements in accordance with a lift plan and workplace procedures
2.2 Risk control measures for hazards identified are checked for implementation in accordance with the lift plan and safe work procedures
2.3 Mobile crane is accessed safely in accordance with manufacturer requirements and safe work procedures
2.4 Pre-start mobile crane checks are carried out and any damage and defects are reported, recorded and appropriate action is taken in accordance with manufacturer requirements and safe work procedures
2.5 Mobile crane is set up correctly with any lifting gear and stabilised as per the lift plan in accordance with relevant manufacturer requirements, including load chart/s and safe work procedures
2.6 Counterweight/s are set up as required in accordance with the lift plan, relevant manufacturer requirements and safe work procedures
2.7 Fly jib and/or luffing fly are set up as required in accordance with specific manufacturer requirements and safe work procedures
2.8 Operational checks are carried out and any damage and defects are reported, recorded and appropriate action is taken in accordance with manufacturer requirements and safe work procedures
2.9 Crane logbook is checked to confirm current compliance, is correct for the crane type, is completed and signed and required rectifications have been signed off in accordance with manufacturer requirements and safe work procedures
2.10 Weather and work environment conditions are assessed to determine any impact on mobile crane operations in accordance with manufacturer requirements and safe work procedures
2.11 Weight of the load is confirmed
2.12 Derated Working Load Limit (WLL) of lifting equipment resulting from selected slinging techniques is calculated and confirmed as suitable to meet the requirements of the lift plan
2.13 Suitable lifting points and slinging techniques are identified
2.14 Lifting equipment and gear are confirmed as ready for safe use
2.15 Load destination stability is confirmed ensuring it is able to bear the load and is prepared for safe access and landing
3 Perform work/task
3.1 Lifts are determined to be within the RC of the mobile crane in accordance with the load chart/s and lift plan
3.2 Boom/jib and hook block are safely positioned over the load following directions from associated personnel in accordance with the lift plan and safe work procedures
3.3 Main and/or auxiliary hook, including any lifting gear where required, are connected to the load and used safely in accordance with the lift plan, safe work procedures and manufacturer requirements
3.4 Test lift is carried out in accordance with dogging and safe work procedures
3.5 Loads are transferred using relevant crane movements and tag lines, as required, in accordance with lift plan and safe work procedures
3.6 Load and crane movement is monitored constantly and crane is operated safely in accordance with lift plan and safe work procedures
3.7 All required communication signals are correctly interpreted and followed whilst crane is operated in accordance with the lift plan and safe work procedures
3.8 Load is lowered and landed safely in accordance with lift plan and safe work procedures
3.9 Lifting gear is positioned for safe disconnection from the load and crane is positioned for next task in accordance with lift plan and safe work procedures
3.10 Lifting equipment and gear are inspected for defects, and defective items are isolated, labelled and reported
4 Pack up
4.1 Crane boom/jib, lifting gear and associated equipment are stowed and secured as required in accordance with manufacturer requirements and safe work procedures
4.2 Crane fly jib and/or luffing fly and counterweight/s are removed to storage position and secured as required in accordance with manufacturer requirements and safe work procedures
4.3 Relevant motion locks and brakes are applied as required in accordance with manufacturer requirements and safe work procedures
4.4 Outriggers, plates and/or packing are stowed and secured in accordance with manufacturer requirements and safe work procedures
4.5 Crane is shut down and secured to prevent unauthorised access/use in accordance with safe work procedures
4.6 Shutdown crane checks are carried out in accordance with safe work procedures and manufacturer requirements